Quantcast
Channel: Heavy Equipment Forums - Forklifts/Telehandlers
Browsing all 679 articles
Browse latest View live

Genie electrical ?

Hi everyone. I joined here cause I bought a genie Z45/22. What is the proper way to remove and install wires on the terminal block in the ground control panel? Thank you.

View Article


terex tb42 oscillating front axle

I can not get the front axle to unlock. I have extended the boom and lifted past 15 deg, then retracted the boom fully then lowered to the ground per the manual and I can not get the axle to unlock....

View Article


Image may be NSFW.
Clik here to view.

Just some work pics

I got suckered into working on a customer lift is usually not for me, but this one interested me. This cylinder was different not the run of the mill . It had a unique retaining of the cap. A pin slid...

View Article

Image may be NSFW.
Clik here to view.

Komatsu FB10RS-12 won't operate, but can be switched on, and gives 'Error 20'

Since 'error 20' is an error on the travel motor, I took out the travel motor's PCB and found out that a few of the mosfets were busted. I have tried to fix it by replacing a few of the busted FS70UM...

View Article

Question to all telehandler drivers

Hi folks. I'm wanting to find out if anyone operates a telehandler which has a delay when lowering the boom. By that I mean push the stick forward, wait 1.5 seconds then the boom starts to move. I've...

View Article


Clark IT60 Wiring Diagram

A friend of mine had some tweekers come through his yard stealing anything metal and they stole the radiator and cut out all the wiring on this diesel forklift. The thing is older than my kids and I...

View Article

Terex tb44 - oem joysticks intermittent

1999 TB44 has intermittent joysticks (3 sticks). Grounds look good and I'm getting power to the sticks. I have OEM Controls on the machine. After machine warms up (5-10 minutes) I will be able to use...

View Article

Lull 644 control manifold

Good day to everyone, i am working on a lull 644 forklift,was down for awhile being the hydraulic pump blown up itself,new pump has being installed,the control manifold was also taking out by others,i...

View Article


Upright MX19 Scissor Lift directional control

Hello: Anyone have experience with an Upright MX19 scissor lift? Tech is struggling to find electrical schematic that will allow him to wire directional (forward/reverse) control. Any help is...

View Article


LULL 844c -42

When the lift is first started and hydraulics are cold , most functions will only work momentarily . Has 450 psi pilot pressure but Pump 2 port drops off at about 900 -1000 psi and function stops . I'm...

View Article

Hyundai 30D-7 brake chatter

Hello all! New to the forum and new to being a forklift owner. I recently purchased a Hyundai 30D-7 with 4200 hours on it. Mechanically it seems in very good shape, with the exception of the brakes....

View Article

2000 snorkel TB120 motion packs

Sup fellas,I recently against my better judgment purchaced a 2000 Snorkel TB120 to recondition and sell...there are many many reasons why this was a bad idea,and for what I paid for it.....like I SAID...

View Article

TMZ 34/19 membrane

Hi Everyone this forum has helped a lot with this machine thanks. I have an issue with it that I have had to replace the lower membrane twice in 2 years. This machine only gets used 10 times a year....

View Article


Genie tmz 50/30

Hi all, im new to this heavy equipment stuff but not electronics. I just got out of the Marine Corps and started a new career, Boss is asking me to try and fix his genie with my aviation electrical...

View Article

Lull Alternator

Can anyone help me with the proper alternator part # for a 95 644 Highlander with the JD 4039D engine?

View Article


Comparing between jlg cherry picker and genie cherry picker

Hi, Every body. i want to by one cherry picker machine type 18m platform height, i am considering between Genie or JLG. i do not have many knowledge about machine. Some body can please help me to asset...

View Article

Clark C500-40 Mast Cylinder Lubrication?

We've recently purchased an old Clark C500-40 Forklift and the mast needs lubrication. I don't see any grease fittings anywhere on the mast. How, and with what lubricant, should we be lubricating the...

View Article


Grove Manlift AMZ106XT

Working on this Manlift for three days with no high speed. Have completed checks for all electrical, all good. Have checked different system hydraulic pressure, reading up to 2500 PSI. Would like to...

View Article

JCB 506 C telehandler

I have a JCB 506C telehandler and after being started twice in short time it will slowly turn over with the key. If you leave the key off and jump the starter the engine will spin fine. I do not have...

View Article

Please help with Lull 644 Highlander 2

Really hoping someone out there can help me with a vintage Lull 644 Highlander 2 I just purchased for help building our log home. Here are my specs: Lull 644 TT-34 Highlander 2 Serial #: P-118N Engine...

View Article
Browsing all 679 articles
Browse latest View live