fuel leakin down on 844 lull
I have a 2003 944 E lull that the fuel will leak down in the fuel filter after the machine has been cut off. it runs fine ounce I crack the #2 injector to get it running but I have to do this every...
View ArticleTelehandler used as Backhoe
Does anyone have experience ditching with a telehandler? I'm thinking of attaching a Bobcat implement up front for simple ditching like footings/septic lines/water and electrical lines. Anyone done...
View ArticleClik here to view.
Snorkel TBA60D Lift cylinder seal failure
I have a '90 model TBA60D man lift. The lift cylinders seal has fail and it's pouring fluid. This change out will not be a 1 hour job. LOL. Are there any HE members that have experience pulling the...
View ArticleGenie tmz 34/19 need help
Just bought a 2002 tmz 34,wasn`t running,was told it needed platform controller membrane pad to get it going,I replced that and put in new batteries,switched it on,it has man outriggers,lights on all 4...
View ArticleAnother TMX-34/19 with problems
So I have a 34/19 with issues. not sure where to start, but from the ground controls... turn the key on, lights flash, lot's of clicking--sounds like it's coming from some solenoids, the feet were...
View ArticleSkytrack Boom extension issue
ok, have a 10042, will not extend all the way out, on the intermediate boom, there are letters. Typically it will extend out past "G", right now it won't show the letter "F". The wear pads are a little...
View ArticleCAT TL 642c AC
Hi , I have a CAT TL 642 c with an AC problem. It appears the fans located on the roof evaporator unit had seized and now after replacing them with new ones they are not powering up, to cool the...
View ArticleLooking for a smaller telehandler
Good day! Haven't been here in a while. I work at a thermo-electric generating facility. We have a couple of forklifts. A little 'traditional' Hyster and a medium-large Mustang 1155. The problem is the...
View ArticleLoed 534-8
Does anyone know where I could find information or a manual on the hydraulic drive system.
View ArticleJCB 525hl-4B - Help with hydrauli hose change
Hi all, I need a bit of advice with my JCB 525hl-4b. One of the the main hydraulic hoses to the fork tilt cylinder/ram split the other day. I've not been able to source a new one yet so have decided to...
View ArticleGenie 45/25 Start Problems
I have a Genie 45/25 2006 that is having issues starting. On a cold start (first thing in the morning) it starts fine, like it's brand new. if I turn it off and then try to start it again, nothing,...
View ArticleBroken TC30
Just started a new job and have been tasked with cleaning out the company's warehouse. One of the obstacles to completing that task is a Cat TC30. Apparently it's been sitting in the same place for...
View ArticleGenie S60 manlift refubishing
We have a genie S60 manlift that we are planning on doing some refurbishing work on. Its in pretty good shape for the most part but the wiring harness is completely shot on it. We plan on completely...
View ArticleSkytrak stalling
Hi, I am new to the site but love reading all the info., very helpful. I own a Skytrak 8042 and recently it has stalled on me a few times, once while driving (in 2nd, not high revs), and a couple times...
View ArticleCaterpillar VC60D SA diesel forklift, transmission not engaging
Hey guys, my company is in the warehousing/storage industry and one of my forklifts has been down for a while. It's an early 90's model Cat VC60D SA. For the life of me, I can't get it to engage...
View ArticleClik here to view.
Clark Forktruck Troubleshooting?
Hello I am trying to troubleshoot a Clark fork truck #060-86-768 for a no start condition. This truck has a 6000 lb capacity. I have the engine now turning over, but it will not start. I have found I...
View ArticleJCB 520/50 loadall
I have to change the hydraulic pump on the above machine . I would be grateful for any tips for this , or any possible snags I might encounter. I have new oil , new pump , and gasket to hand , and I...
View ArticleOld Lull 844tt 34 questions
Thanks for the Lull 844 manual and parts info! I have opened the rear right hub and discovered one of the planetary gear pins was bent enough to periodically bind and stop the machine. This was left...
View ArticleWhat year is my Lull 844 tt
I have seen the lull chart on s/n, age, etc. but couldn't figure my machine. S/N is DO983TN if anyone can tell me more. Thanks, Mike
View ArticleInformation on a Loed 534
We purchased a Loed 534 in June. Does anybody have a service manual for this?
View Article